PTO and Machinery Safety on the Farm
Shields, shutoffs and a rule never to reach into a running machine prevent the worst farm injuries.
A power take-off shaft spins at hundreds of revolutions per minute with a grip no person can overcome. Clothing, hair or a shoelace caught on an unguarded PTO can pull an arm or leg into the shaft within a fraction of a second. The same is true for augers, conveyors, balers, corn heads, choppers and other moving parts. Entanglement injuries cause amputations and deaths, and they often involve a person who "just reached in for a second" or who was clearing a jam while the machine was running. This article explains how to prevent machinery injuries through guards, procedures, training and habits. It is educational. Always follow the manufacturer's instructions for each machine, and use qualified training. For guidance, see NIOSH and OSHA agricultural operations.
Why machinery hurts people
- Moving parts are hard to see in dust, noise and low light.
- Entanglement happens fast. There is no time to react once caught.
- Stored energy. Hydraulic pressure, springs, flywheels and raised implements can move after the engine stops.
- Shields are removed and not replaced, or are damaged.
- People take shortcuts when time is tight or when jams occur.
- Loose clothing, long hair, jewelry and drawstrings.
- Fatigue and distraction. See farmer stress, fatigue and safety.
- Untrained or young operators.
Guards and shields
Guards are the first line of defense.
- PTO shaft shields. Every PTO connection should have a master shield on the tractor, a complete driveline shield on the implement shaft and shields on the implement input connection. Shields should be free to rotate on bearings so that if someone contacts them, they stop turning. Replace broken or missing shields at once.
- Machine guards. Gears, belts, chains, sprockets, fans and augers should be covered by guards in good condition.
- Safety interlocks and switches. Do not bypass them.
- Warning decals. Keep them readable and replace faded ones.
- Do not step over a rotating PTO shaft. Even a shielded shaft can be dangerous if the shield is damaged.
Check your guards at the start of each season, and after repairs. The PTO and machinery safety audit provides a checklist.
Lockout before you touch
Most machinery injuries occur during repair, adjustment, cleaning or unjamming, while the machine is still powered or can move.
Before cleaning, servicing or clearing a jam:
- Disengage the PTO or power.
- Shut off the engine.
- Remove the key, and keep it in your pocket.
- Wait for all moving parts to stop completely.
- Relieve stored energy: lower raised implements to the ground or block them securely, release hydraulic pressure and secure springs.
- Lock out and tag out power sources on stationary equipment such as augers and conveyors, with a personal lock where possible.
- Check that nothing can start or move before putting hands in the machine.
- Tell others the machine is being serviced.
Never rely on raised hydraulics alone to hold a load. Use stands or blocks. Never work under a machine supported only by a jack.
Clearing jams
Jams create pressure to "just pull it out." Do not. Shut down and lock out first. Use tools, not hands, to clear plugged material after the machine has stopped. This is a hard habit to build but one of the most important.
Specific machines
Augers and conveyors
Keep intake guards and shields in place. Do not climb on or step over running augers. Never feed material by hand into an auger intake. Use a lockable disconnect near the auger. Keep children away. See grain bin entrapment prevention.
Balers and wrappers
Balers have chains, belts and rollers that can grab. Shut down and lock out before clearing or lubricating. Use proper tools to feed or clear bales.
Combines, choppers and corn heads
Combine heads, chains and rollers are notorious for entanglements. Never unplug a corn head while it is running. Wait for the machine to stop and use the lockout steps.
Mowers and shredders
Throwing objects and spinning blades cause injury. Keep bystanders away, and stop before dismounting. Keep guards and deflectors in place.
Skid steers, loaders and telehandlers
Use seat belts and restraint bars, keep loads low and avoid people in the line of travel. Ensure working lights and backup alarms.
Hay equipment and rakes
Wheels, tines and hydraulic cylinders can crush or pinch. Block raised parts before working under them.
Hand tools and shop equipment
Grinders, drills and welders need guards, eye and hearing protection and training. Control fire risk. See farm fire prevention checklist.
Clothing and personal habits
- No loose clothing, dangling drawstrings, scarves or jewelry around machinery.
- Tie back long hair and use a cap.
- Wear sturdy boots with good traction.
- Wear gloves only when appropriate, and not near rotating parts where they could catch.
- Use hearing protection and eye protection as needed.
- Avoid rushing, distraction and alcohol or drug use. Do not use phones while operating.
- Keep communication clear. Use hand signals or radios.
Hitching and implement connections
Many PTO injuries occur during hookup. Shut off the tractor and set the brake before connecting. Make sure the shaft length is correct for the implement, and use a locking collar. Ensure that the driveline shield is on and in good condition. Use a drawbar and approved hitching points. See tractor rollover prevention.
Maintenance
Well-maintained equipment is safer. Follow the manufacturer's service schedule. Check shields, brakes, hydraulic lines, lights and warning devices. Replace worn parts. Keep a record. See the tractor maintenance risk checklist and machinery replacement and downtime risk. Keep tools and a first aid kit nearby.
Training and rules
- Train every operator on each machine. Include new workers, family and seasonal staff. See farm employee safety orientation and hired farm worker safety training.
- Set rules: no riders, no bypassing guards and lockout before maintenance.
- Supervise young workers closely, and follow child labor rules. See youth farm work and child labor rules.
- Hold short safety talks before busy seasons.
- Encourage reports of unsafe equipment.
- Fit safety into the program. See building a farm safety program.
Emergency response
If someone is caught in a machine:
- Shut off the machine immediately, by the nearest emergency stop or by stopping the engine.
- Call 911. Give the farm address and describe the situation.
- Do not try to reverse or free the person with the machine running.
- Control bleeding with direct pressure or a tourniquet if trained, and keep the person warm and calm.
- If a body part is amputated, wrap it in clean cloth, place it in a sealed bag and keep it cool but not directly on ice, and send it with the person to the hospital.
- Have someone meet the ambulance at the road.
Keep first aid kits on tractors and in shops. Train workers on basic first aid. See farm emergency contact plan.
Insurance and legal considerations
Machinery injuries can lead to workers compensation claims, liability claims and costly downtime. See farm liability insurance guide and hiring farm workers: compliance basics. Federal rules under OSHA and state laws set requirements for guarding and training in some circumstances. Ask your insurer about safety programs.
Stay informed
For safety stories and farm news, see FARM.FM Farming, FARM.FM Rural Life and FARM.FM News. For a story with all its guards in place, FARM.FM Jokes has no moving parts.
Frequently asked questions
Do I really need to shut off the tractor to unclog a machine?
Yes. Disengage power, shut off the engine, remove the key and wait for all motion to stop. Most entanglement injuries happen when people reach into running equipment.
Can I operate with a missing PTO shield?
No. Replace the shield before use. A missing or damaged shield is a leading cause of serious injury.
What should I wear around machinery?
Close-fitting clothing, tied-back hair and sturdy boots, with no loose items that could catch.